Corrosion-Resistant 5A05 Aluminium Circle Disc

• Customization: Available
• Application: Kitchen Appliances,Reflector Panel, Traffic Sing
• Certification: ISO9001, ASTM, GB, EN
• Model NO.: 5A05
• Technique: Hot Rolled/Cast Rolled
• Grade: 5000 Series
• Temper: O,H12,H14,H16,H18,H22,H24,H26,H32,H34
• Surface Treatment: Mill Finish
• Alloy: Alloy
• Thickness: 0.4--150mm
• Diameter: 80-1200mm
• Transport Package: Export Standard Wooden Case
• Specification: According to Customer Requirement
• Trademark: Chalco Aluminum
• Origin: Henan China
• HS Code: 7606121000
• Production Capacity: 10000mt/Month

Product Description

5A05 aluminium disc
 
CHALCO aluminium manufactures alloy 5A05 aluminium disc with with higher strength and excellent in forming and corrosion resistance that can be subject to further treatment by the following methods: deep drawing, spinning,etc.
 
5A05 Al-Mg system for anti-rust aluminum alloy, non-heat strengthened. Good weld ability, corrosion resistance alloys can still apply to welding, atomic hydrogen welding, gas welding, welding. Its mach inability, the annealed state is poor, half-cold hardening state is still good.

5A05 alloy commonly used for manufacturing processes require high ductility, corrosion resistance, withstand moderate load of welded pipes, welded mailboxes and other liquid containers, as well as other parts; wire used for welding and rivets, rivet requires anodized. In other countries, the approximate alloys (such as 5456) for the production of armor plates, high-strength structural parts. 
Aluminum circle is widely used in electronics, daily chemicals, medicine, automobile accessories,aerospace, military, mold, construction, printing ,non stick pan, pressure cooker,lampshade, water heater shell and stretching tank etc.It is one of the most used deep processing products of aluminum alloy plate and strip.

 Alloy: 5A05
Temper: O, H12, H14,H16,H18,H22,H24,H26,H32,H34
Thickness: 0.4~150mm
Diameter: 80~1200mm
Surface:Mill finish
 
Chemical Properties

Alloy	Si	Fe	Cu	Mn	Mg	Cr	Ni	Zn	Ga	V	Ti	Other	Min.A1
5A05	0.50	0.50	0.10	0.30-0. 6	4.8-5.5	-	-	0.20	-	-	-	0.15	Remainder

 

Section	Alloy	Characteristics	Application
5000 series	AA5A02 AA5A05 AA5005 AA5052 AA5754 AA5454 AA5083	Have higher strength than 3000series and excellent in forming and  corrosion resistance		Spare parts, Rocket bottom,Pressure Vessel,Oil tanker cover,Cover in outdoor,etc.

 
Diameter List

>=20	>=140	>=170	>=200	>=250	>=300	>=400	>=500	>=600	>=700	>=800
20	140	170	200	250	300	400	500	600	700	800
25	141	172	203	252	305	405	505	610	705	810
93	142	173	205	254	310	410	510	615	710	838
100	143	175	210	255	312	420	515	619	720	890
105	144	176	211	258	315	425	520	630	730	902
109	145	177	212	260	320	430	525	635	740	945
110	147	178	215	267	325	435	530	645	760	960
112	149	180	216	268	330	440	540	650	770	1000
115	150	181	217	270	335	445	545	655	780	1150
118	153	182	218	272	340	450	550	665		1200
120	154	183	220	274	345	455	560	670
121	155	184	221	275	350	460	565	680
122	157	185	222	277	355	465	570	690
123	158	188	225	278	360	470	575
124	160	190	226	280	364	475	580
127	161	192	230	282	368	480	585
128	162	193	233	285	370	485
129	163	195	235	290	375	490
130	164	198	237	292	380	495
132	165		238	293	385
133	166		240	295	390
134	167		242		395
135	168		245
136	169		249
137
138
139

 
Mechanical properties:
Tensile strength σb (MPa): ≥225
Conditions yield strength σ0.2 (MPa): ≥110
Elongation δ10 (%): ≥15
Note: The vertical pipe at room temperature mechanical properties
Sample Size: All Thickness
 
 Heat treatment:
1) Homogenization: Heat 460 ~ 475 ºC; holding 12 ~ 14h; air cooling.
2) Rapid thermal annealing: heating 310 ~ 350 ºC; holding time 30 ~ 120min; air or water.
3) High temperature annealing: heating 310 ~ 335 ºC; finished thickness ≥6mm or <6mm, the holding time of 30 ~ 180min or 30 ~ 120min; air cooling.
4) Low-temperature annealing: heating 250 ~ 300 ºC or 150 ~ 180 ºC; holding time of 1 ~ 2h or air-cooled 2 ~ 3h Status: aluminum and aluminum alloy extruded seamless pipe (H112 condition)

5A05 Aluminium Alloy disc Features:
1.Alloy 5A05 aluminium disc with higher strength and excellent in forming and 
corrosion resistance
2.Wide range of selection on discs' size including customized shape and size.
3. Excellent reflectivity, good for Polishing;
4.Excellent deep drawing and spinning quality.
5.Good